8IGHT-E 4.0 KIT: 1/8 4WD ELECTRIC BUGGY

FEATURED PRODUCT VIDEO

CHASSIS CALL-OUT

  1. DURABLE 4MM HARD-ANODIZED 7075 T-6 ALUMINUM CHASSIS
  2. TWO BATTERY AND ESC LOCATIONS
  3. LARGE-BEARING SPINDLES AND HUBS
  4. VARIABLE MOTOR AND CENTER DIFFERENTIAL ANGLES
  5. 15" CASTER BLOCKS WITH ADJUSTABLE SPINDLE HEIGHT
  6. ALUMINUM SHOCK CAPS WITH THREADED BLEEDER HOLES
  7. MOLDED DRIVESHAFT AND DOG BONE BOOTS
  8. ALUMINUM SHOCK TOWERS WITH UPDATED CAMBER LINK AND SHOCK LOCATION HOLES

FEATURES

REVISED SUSPENSION GEOMETRY

New suspension geometry makes it easier for drivers of all experience levels to turn faster lap times with fewer mistakes, particularly when harnessing the power of a high-output brushless motor system.

Revised Suspension Geometry

VARIABLE MOTOR AND CENTER DIFFERENTIAL ANGLES

Two different center plates for the bottom of the chassis are included. The stock center plate puts the motor and differential directly in line with the chassis. The optional center plate rotates the motor and differential 4.4 degrees, creating equal angles between the front-center and rear-center dog bones.

Variable Motor and Center Differential Angles

TWO BATTERY AND ESC LOCATIONS

The chassis offers two locations for the battery and ESC. With the battery in the forward location and the ESC in the rear of the car, the vehicle has more forward weight bias which improves stability on high-speed tracks.

Two Battery and ESC Locations

LARGE BEARING SPINDLES AND HUBS

Front spindles and rear hubs have been revised to accept a larger 8 x 16 x 5 outer bearing for increased durability.

Large Bearing Spindles and Hubs

ADJUSTABLE CASTER BLOCKS

The adjustable, 15-degree caster blocks make it possible to tune dog bone plunge by changing the height of the spindle.

Adjustable Caster Blocks

NEW BLEEDER SHOCK CAPS AND SEALS

The new bleeder shock caps and internal seals allow for easier rebuilds while using an emulsion shock setup. New bushings that press into the shock cap further improve durability.

New Bleeder Shock Caps and Seals

DRIVESHAFT AND DOG BONE BOOTS

Molded rubber boots on the CVAs and center drivetrain dog bones increase U- joint life by holding lubrication in and keeping dirt out.

Driveshaft and Dog Bone Boots

REDESIGNED SHOCK TOWERS

The machined aluminum shock towers have new camber link and shock location holes that give racers more tuning options for changing track conditions.

Redesigned Shock Towers

CAB-FORWARD BODY

The cab-forward body moves aerodynamic pressure further forward on the car, which improves steering.

Cab-Forward Body

PRODUCT SPECIFICATIONS

Type:
Electric Buggy
Scale:
1/8
Length:
19.6 In (497mm)
Width:
12.1 In (308mm)
Height:
7.1 In (180mm)
Ground Clearance:
2.4 In (60mm)
Wheelbase:
12.7"-12.9" (323-327mm)
Weight:
Varies On Equipment Used
Chassis:
4mm Plate, 7075-T6 Alumimum, Hard Anodized
Suspension:
4 Wheel Independent
Drivetrain:
4WD, Shaft Driven
Tire Type:
Not Included
Motor or Engine:
690 Size Not Included
Speed Control:
Not Included
Radio:
2 Channel, Not Included
Servos:
Not Included
Batteries:
Not Included
Charger:
Not Included
Gear Pitch:
MOD 1
Kit/RTR:
Kit
Shock Type:
Aluminum Oil Filled
Body:
8IGHT-E 4.0 Cab Forward, Clear, Pre-Trimmed
Ball Bearings:
Yes
Experience Level:
Advanced
Recommended Environment:
Outdoor
Assembly Time:
5-7 Hours
Is Assembly Required:
Yes
23,900 THB
จำนวน:

  • TLR04003_b0.jpeg
    CHASSIS CALL-OUTDURABLE 4MM HARD-ANODIZED 7075 T-6 ALUMINUM CHASSISREDUCED FRONT DRIVESHAFT ANGLEBALL BEARING THROTTLE AND BRAKE ACTUATORSLARGE-BEARING SPINDLES AND HUBSREVISED CHA...
    23,900 THB

  • TLR03013_b0.jpeg
    FEATURED PRODUCT VIDEOCHASSIS CALL-OUTLIGHTWEIGHT 2.5MM HARD-ANODIZED 7075 T-6 ALUMINUM CHASSISVLA FRONT SUSPENSION3-GEAR LAYDOWN/STAND UP TRANSMISSION (LAYDOWN SHOWN)UPDATED BALL ...
    15,900 THB
Visitors: 526,804