DDL-DDG001 Dori Dori Gyro for MRD ZERO

Dori Dori Gyro for MRD ZERO （Prototype）Option Parts for MRD ZERO MRD ZERO [Product Description] A drift-dedicated gyro unit developed for the MRD ZERO, designed exclusively for the Mini-Z AWD MA-020 circuit board. It replaces the Kyosho genuine gyro unit and connects to the MA-020 board with the included harness. The gyro sensor, microcontroller, and control software are all newly designed from the ground up. Development focused on suppressing “hunting” which is the rapid left-right steering twitch that occurs during drifting and straight-line driving. On top of high-speed 1 kHz control…

In stock

SKU: DDL-DDG001
Category: DDLABO
Tags: DDG

Description / 商品説明

 

[Product Description]
A drift-dedicated gyro unit developed for the MRD ZERO, designed exclusively for the Mini-Z AWD MA-020 circuit board.
It replaces the Kyosho genuine gyro unit and connects to the MA-020 board with the included harness.
The gyro sensor, microcontroller, and control software are all newly designed from the ground up.
Development focused on suppressing “hunting” which is the rapid left-right steering twitch that occurs during drifting and straight-line driving.
On top of high-speed 1 kHz control (1,000 updates per second), it employs a multi-stage noise filter designed from actual measured chassis vibration.
It suppresses unwanted steering movement when running straight, while responding sharply on drift entry and transitions.

 

[Compatible Boards]
Compatible with the following MA-020 boards:
– MA-020 Sports Readyset (blue antenna)
– MA-020 Readyset (white antenna)
* Not compatible with MINI-Z EVO or MINI-Z PRO series boards.

 

[Adjusting Gyro Gain]
When using a KT-19 / KT-531P transmitter, adjust the gyro gain with the dial on the MA-020 board, the same way as with the stock unit.
When using the separately sold FS-RM005 module with one of the following transmitters, gyro gain can be adjusted from the transmitter side:

– FLYSKY Noble series
– FUTABA 4PM Plus
– FUTABA 6PV
– FUTABA 10PX
– FUTABA 10PXR

 

[Power-On Precautions]
The unit performs automatic calibration when the power is turned on.
Place the car on a flat surface and keep it completely still when powering on.
Calibration completes in about 1-2 seconds once the car is at rest.

During calibration: the LEDs blink alternately left and right
Calibration complete: the unit switches to normal operation
To ensure correct calibration, do not move the car from power-on until calibration is complete.

[About the Gyro Interrupter (MRD-OP001)]
The Dori Dori Gyro cannot be used together with the Gyro Interrupter (MRD-OP001).

The Dori Dori Gyro is a product that replaces the Kyosho genuine gyro unit itself.
Use the Dori Dori Gyro on its own, without the Gyro Interrupter.

<Contents>
Dori Dori Gyro x1
Harness x1
Double-sided tape x1

 

<FAQ>
Q. Can the gain be adjusted?
A. Yes.
The Dori Dori Gyro unit itself has no gain adjustment mechanism.
When using a KT-19 / KT-531P transmitter, adjust it with the dial on the MA-020 board, the same way as with the stock unit.

Q. Can it be used together with the Gyro Interrupter (MRD-OP001)?
A. No.
The Dori Dori Gyro replaces the gyro unit itself, so use it on its own without the Gyro Interrupter.

Q. Can it be used on a normal MINI-Z AWD that has not been converted to an MRD ZERO?
A. Since it connects to the MA-020 board, it will be recognized and will operate.
However, this product was developed and tuned exclusively for the 2WD drift-spec MRD ZERO.
Use outside the MRD ZERO — such as grip driving on a MINI-Z AWD chassis — is outside the scope of support.

Q. Can it be used with the MINI-Z EVO or MINI-Z PRO?
A. No.
The supported boards are the MA-020 Sports Readyset (blue antenna) and MA-020 Readyset (white antenna).

Q. How is this different from the Kyosho stock gyro unit + Gyro Interrupter?
A. The gyro sensor, microcontroller, and control software are all newly designed.
In particular, noise filters designed from measured chassis vibration and straight-line detection logic focus on suppressing the hunting that occurs during drifting and straight-line driving.

Q. After power-on, the LEDs keep blinking alternately left and right.
A. This indicates that automatic calibration is in progress.
Place the car on a flat surface and leave it still. Calibration normally completes in about 1-2 seconds.

Q. The car pulls to one side while driving.
A. Calibration at power-on may not have completed correctly.
Turn the power off, place the car at rest on a flat surface, and turn the power on again.
Do not move the car after power-on until calibration is complete.
 

 

This product is an option part developed for the MRD ZERO.
 

Not compatible with the MINI-Z EVO or MINI-Z PRO series.
Please note that the product specifications may change without prior notice for improvement.
 

MINI-Z” is a trademark of KYOSHO Corporation. This is a third-party option part and is not affiliated with KYOSHO Corporation.
 

https://youtu.be/gOnLAAI3OUM